- Business-class 802.11n WLAN access point
- PoE (Power-over-Ethernet) as standard
- Dual isolated LAN interfaces
- 4-Port Ethernet Switch
- Detatchable Antennae - Can be replaced
- with uni-directional or high-gain
- Wireless Encryption : WEP, WPA, WPA2
- 802.11b/g Backward Compatible
- Repeater/Bridge/Access Point/Station Modes
- Wireless Client Isolation
- 802.1q VLAN Tagging
- Up to four distinct SSIDs (for VLANs)
- MAC Address Filtering
- Radius / WPA User Authentication
- 802.1x User Authentication
- WDS (Wireless Distribution System)
- WMM (Wireless MultiMedia)
- WPS - WiFi Protected Setup
- Built-in Site Surveyor
The DrayTek Vigor AP-800 is a standalone wireless access point, ideal
for adding wireless connectivity to an existing LAN, or for expanding the
range of an existing wireless LAN by using the WDS features.
The AP-800 features multiple levels of wireless security. Encryption
using WEP, WPA, WPA2 (802.11i) is available you can also use the access
control list (ACL) to specify the hardware addresses of clients which are
permitted to connect (by MAC hardware address). Any unauthorised hardware
is refused access.
For additional user authentication, you can activate 802.1x RADIUS
(Remote Authentication Dial-in User Service) which allows you to centrally
manage and store user names and passwords either within the AP-800 setup
itself (thus not needing any external server) on an external radius server
which can permit time limited, temporary or continuous access to your
clients as required.
The Vigor AP-800 supports the 802.1q VLAN protocol so that if it is
connected to an 802.1q enabled LAN, it can split tagged data (whether its
different subnets or intended for different users) and broadcast each on
its own SSID. This means, for example, that your guest WiFi access is
provided on a separate isolated SSID with no access to your company data.
(802.1q Feature ETA Q1/2011)
USB Printer Port
The AP-800 has a USB interface into which you can connect a regular
printer. That printer is then accessible from any wireless or wired PC
which connects to the AP-800, or a PC anywhere else on the network to whick
the AP-800 is connected. This is ideal to provide printer access to
wireless laptops but could also be used for installing a printer elsewhere
in your home/office by using a pair of AP-800s to make a bridge.
WMM - WiFi Multimedia
The AP-800 implements intelligent wireless traffic prioritization for
the most efficient management of wireless traffic by using the Wi-Fi
Multimedia standard (WMM). WMM defines Quality of Service (QoS) in Wi-Fi
networks. It is a precursor to the upcoming IEEE 802.11e WLAN QoS standard,
intended to improve timing critical applications such as audio, video and
voice applications over WiFi. WMM adds prioritized capabilities to Wi-Fi
networks and optimizes their performance when multiple concurrent
applications, each with different latency and throughput requirements,
compete for network resources.
WPS - WiFi Protected Setup
Wireless Security (encryption) is important to protect your data
(privacy) but also to prevent unauthorised people from accessing your
network or your Internet connection. The WPS system means that instead of
having to create and enter long encryption keys, you can activate WPS
registration. To activate, you press and hold the WPS button, then activate
the WPS function on your PC; the two devices then automatically exchange
The same button on the AP-800 also serves as a physical on/off switch
for the Wireless LAN if you wish to quickly disable it at any time, whilst
still leaving your wired ports active.
By the addition of a simple plug in 'N65' USB module, the AP-800 can
operate in the alternative '5.8Ghz' band simultaneously with the standard
2.4Ghz band. As it's simultaneous, you can still use the 2.4Ghz band for
some devices. The 5.8Ghz band is much less widely used and therefore less
congested. Your PC needs to support this band to take advantage but if it
doesn't you can add the same 'N65' USB 'dongle to the PC to add it. The
dual-band upgrade should be available by the end of 2011 (estimated); price
to be confirmed.
WDS & Repeater Modes
The DrayTek AP-800 can act as a standalone wireless access point, ideal
for adding wireless connectivity to an existing LAN but also operates in
several other wireless modes to provide enlarged wireless coverage or
wireless bridges to other parts of your LAN. Many different configurations
This mode joins two parts of the same logical network which cannot be
otherwise connected by cables, for example between two adjacent buildings.
As the AP-800 has a built-in 4-Port switch, you can then connect up to 4
wired devices/PCs directly to it.
As a repeater, the AP-800 can extend the wireless coverage of a network.
You can add multiple units to extend the range in multiple directions or
multiple hops (for best performance, more than two is not recommended due
to latency and channel congestion which can result).
In 'Station Mode' a remote station (computer or other device) can
connect to the AP-800 using a regular ethernet cable, but the AP-800
connects to the remote LAN over wireless. The AP-800 has a built-in 4-port
Ethernet switch so you can connect up to 4 client devices directly by wired
Ethernet (100BaseT RJ45).
The AP-800 can support two completely independent LANs; each is
connected via its own independent RJ45 Ethernet interface. There are
Ethernet RJ45 interfaces for LANA (4 ports) and LAN B (one port). These
networks remain completely isolated from each other. Each LAN is assigned
its own separate Wireless SSID so they remain separated even on the
Wireless LAN. This is the equivalent of having two completely separate
access points and ideal for public and private networks in the same
location or wireless LANS for two separate companies.
Having two physical LAN interfaces provides a much simpler alternative
to using tagged VLANs (which requires additional switching hardware with
VLAN support) and a Radius server for authentication. It is also much
easier/quicker to set up.
The AP-800 supports PoE (Power over Ethernet) as standard (built-in) so
if the AP-800 is connected to a PoE enabled Ethernet switch or PoE
injector, you don't need any local power to the unit (power supply) - the
AP-800 will take its power from the Ethernet cable. This is ideal for
situations where you do not have mains power available in the exact
location where you want to install the AP-800 or just for general aesthetic
neatness, perhaps where the AP-800 is installed somewhere prominent
The AP-800 is also supplied with an AC/DC mains PSU for installations
where you are not using PoE.
|Sinch Search Cache||AP800 P800 800 AP80 AP8 74TL 4TL 74T 50843 0843 843 5084 508 Draytek Vigor Pro Wireless Access Point with PoE igor gor Vigo Vig ireless reless eless less ess Wireles Wirele Wirel Wire Wir ccess cess ess Acces Acce Acc oint int Poin Poi ith wit 4719853551367|